Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Compton?
Gate parts and welding work in Compton typically runs $180 to $850 for most residential repairs, with common fixes like hinge replacement, latch repair, and steel welding landing in the $225 to $475 range. Full gate section fabrication or heavy-duty welding a commercial slide gate can reach $1,400 or more depending on steel gauge and size. Old, sun-baked steel and tired hardware on gates of a certain age are the biggest reasons Compton quotes land where they do, and we price every job per the written estimate so you know the number before we start.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what the parts and labor typically look like for a Compton residential or light-commercial gate project. The ranges below are estimates drawn from the work we see on properties around Compton, not a fixed price list.
| Work Item | Typical Cost Range | Notes |
|---|---|---|
| Hinge replacement (per hinge, welded) | $95 – $190 | Includes cutting the old weld and re-welding to the post |
| Latch or handle replacement | $85 – $175 | Manual gate; larger commercial latches cost more |
| Gate framework welding repair (crack or broken joint) | $180 – $400 | Depends on number of joints and access |
| Panel or picket fabrication and welding (per section) | $350 – $900 | Steel gauge and pattern affect the number |
| Roller or track replacement (slide gate) | $120 – $300 | A worn roller is a common cause of sticking |
| Post re-set or footing reinforcement | $250 – $650 | Posts that lean just need to go back to proper footing depth |
| Operator arm or motor hardware (parts only) | $90 – $350 | Varies widely by brand: LiftMaster, FAAC, Viking, and others |
| Wrought-iron repair (rusted or bent sections) | $200 – $500 | Bends and rust at welds drive up the labor |
| Heavy commercial fabrication (per section) | $900 – $1,400+ | Thicker steel, larger panels, access control upgrades |
| Automated gate hardware repair (residential) | $180 – $500 | Diagnostic time for brand-specific operator logic included |
What pushes a Compton quote up? Steel thickness, whether the gate has to come off its hinges to be welded on a bench, and how much of the frame is corroded at the joints. Rust that started at a weld seam often means grinding back more metal than you’d expect. On the other side, a clean single-joint weld on a manual gate is usually the low end of the range. Brand of operator matters too, especially on automated systems. We work with nine major gate brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so parts for your existing hardware are rarely a problem. When we say we work on the brand you already have, we mean we buy and weld for what’s on your gate, not what we wish was there.
What Affects Gate Parts & Welding Pricing in Compton
Two properties with the same broken hinge can price differently. Here’s what we’re actually looking at when we put a number together.
- Steel gauge and gate size. A 4-foot pedestrian gate with thin pickets is a much faster weld than a 12-foot sliding driveway gate built from heavy box steel. Heavier stock means more grinding, more rod, and longer setup.
- Type of metal. Mild steel, wrought iron, and aluminum all weld differently. Aluminum needs a different process and more time, and a lot of older Compton properties have aluminum gates that need special handling to avoid warping at the heat line.
- Corrosion and prior repairs. A gate welded once before, or one that’s been repainted over rust, takes longer to prep. We have to get down to clean metal or the new weld won’t hold. That prep is real labor.
- Automation and brand. If your gate runs an operator, welding near wiring and sensors takes care. Brand-specific diagnosis saves time on a LiftMaster or FAAC system and adds it on an older or foreign unit where parts have to be sourced.
- Access to the work area. A gate in a wide driveway is easy to work on. A narrow side yard or a commercial gate that has to keep a lane open during the day takes more time and staging.
- Whether it’s a repair or a build. The smallest weld fix is at the bottom of the range. Fabricating a whole new gate section, or converting a manual gate to automated, is at the top.
How to Save on Gate Parts & Welding in Compton
A few things genuinely move the needle on price, and none of them require cutting corners on the weld itself.
- Fix it while it’s small. A hinge that’s starting to sag is a $95 to $190 repair. The same hinge left to tear out the post is a $250 to $650 footing job. Catching welds and hardware early is the single best way to keep costs down.
- Paint bare welds and bare steel. Once a weld cools, painting over the repair and any exposed steel slows rust. Out here, sun and dry air punish bare metal, so a quick coat does more than it sounds like.
- Bundle the work. If you have a broken latch, a sticking roller, and a cracked weld on the same gate, get one estimate for all of it. One visit is cheaper than three.
- Keep your operator maintained. A gate that binds puts strain on the motor and the arm hardware. A properly rolling gate makes the operator last longer, which saves you the $90 to $350 parts bill later.
- Ask what’s actually broken. A decent shop diagnoses brand-specific logic rather than guessing and swapping parts. On LiftMaster, Viking, or Ghost Controls systems, the failure mode tells you what to replace. That’s how you avoid paying for a motor when you only needed a sensor.
We don’t chase upsells. If your gate needs a targeted weld and a new hinge, that’s what the estimate will say. If it needs a full section, we’ll tell you why and show you. Get an estimate in writing and read the scope before you approve anything. It also helps to know whether your gate is the kind that just needs gate repair or whether it’s an operator problem that needs an electric gate repair call. We handle both, so you’re not sizing up two contractors. Estimates are free, and you can reach us at (866) 569-6161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Is Welding a Gate Something You Should Try Yourself?
No, for most people this isn’t a safe DIY job. Welding generates intense UV light that can damage your eyes in seconds, the metal stays hot enough to burn long after the arc stops, and a gate panel is heavy enough to crush a hand or foot if it drops off a hinge while you’re working under it. On an automated gate, the operator’s power and control wiring adds electrical shock risk, and a slip while cutting a weld can send the panel or your torch in an unexpected direction. The dangerous parts of a gate job are the operator’s power, heavy panels that can swing or fall, and slide gates that come off the track. Those are the reasons we recommend a trained technician for anything beyond a visual check. What you can do safely is look before you call: note whether the gate sags, whether the weld is cracked at a hinge or post, whether the rollers run clean, and whether the motor struggles. That observation makes the diagnosis faster and the estimate more accurate.
What Happens When You Call
You tell us what the gate is doing, and we ask a few questions: manual or automated, what brand if there’s an operator, which parts look bent or loose. Because gate repair is all we do, that call usually narrows it down before anyone comes out. We book a visit, and a technician inspects the gate, checks the welds, hardware, and operator if there is one, and gives you a written estimate with the scope of work. The estimate is free. The price is set per job by that written estimate, so you know the number before we start. From a single broken hinge to a full electric-gate installation, this is the same process. Call (866) 569-6161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
FAQs – Gate Parts & Welding Cost
How much does it cost to repair a gate in Compton?
Most residential gate repairs in Compton run $180 to $500, with simple hinge or latch fixes in the $85 to $190 range and welding repairs in the $180 to $400 range. Heavy commercial fabrication and full section replacement go higher, up to $1,400+. The written estimate sets the final price. Call (866) 569-6161 for an exact quote, and estimates are free.
Is it cheaper to repair my gate or replace it?
Repair is almost always cheaper when the frame and posts are structurally sound: a $200 to $400 weld repair beats a $1,500 to $3,000 new gate. Replacement makes sense when the posts are failing, the steel is rusted through in several places, or the gate is undersized for your access needs. We look at the welds, posts, and hardware and tell you honestly which way the numbers point. We’re not driven to sell a new gate when a fix will do. Call (866) 569-6161 and we’ll walk through it.
Can you fix an automated gate the same day?
Often, yes. A lot of operator issues come down to a limit setting, a sensor, or a worn arm, and we can resolve those on the visit. Same-day service depends on the brand and parts: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule are the systems we work on, and we carry common hardware for them. Call (866) 569-6161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why does brand matter for an electric gate repair?
Brand matters because each operator fails in its own way and the diagnostic logic differs. The parts for a LiftMaster arm aren’t the same as for a FAAC or a DoorKing. A technician who knows nine brands doesn’t guess and swap, which keeps your bill closer to $180 to $350 instead of $500 or more. We’re independent, not tied to any one manufacturer, so the recommendation fits your gate. Call (866) 569-6161 for an estimate.
Do you weld on-site or take the gate to a shop?
Most weld repairs happen on-site so the gate stays on its hinges and posts, with typical cost in the $180 to $400 range. A full panel or section fabrication is easier to build on a bench, and then we install it. The estimate tells you which approach makes sense for your gate. On-site work keeps your property secure during the repair. Call (866) 569-6161 and we’ll talk through the scope.
Why a Gate-Only Specialist for the Welding Work
Plenty of contractors will take a welding job. Fewer do nothing but gates. That focus matters when the weld is a hinge on a 10-foot sliding gate, or when the panel has to line up with an operator that’s already on the property. We keep tools, parts, and troubleshooting knowledge dedicated to this trade. We handle the repair, the automation, and the installation, so a property manager doesn’t need a second contractor when an upgrade gets added to the work. Residential and light-commercial configurations are both in scope. If you’re sorting out how to get your gate working again fast, that’s the whole job for us.
Start with a Free Estimate
Whether your gate needs a weld, a hinge, a roller, or an operator repair, the first step is the same: a call and a free estimate. We serve Compton and the surrounding area, and this is the only kind of work we do. Gate Repair Compton is gate repair, the specialty and the focus. Call (866) 569-6161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Compton market as of 2026. Gate Repair Compton offers free estimates – call (866) 569-6161.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Maria Delgado"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Gabriela Castillo"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Gilbert Herrera