Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Lynwood
Gate repair in Lynwood typically costs between $180 and $2,800 depending on whether we’re re-welding a rusted hinge, resetting a tilted post, or replacing a full operator system. Most repairs on this side of the 90262 are finished the same day because we carry the parts and welding gear on the truck. If your gate drags against a shared block wall, sticks after winter damp, or beeps but won’t open, call (866) 569-6161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
We know Lynwood’s gates the way only a gate-only shop can. Dense blocks of pre-1960 stucco homes, narrow lot lines, parkway trees older than most of the fences they lean against. Every third gate we see here was welded in place because the opening was never wide enough to lift it out. That’s not a problem for us. It’s the job.
Why Lynwood Homeowners Call Gate Repair Compton for Gate Repair
Because gate repair is all we do. Not a handyman service that also does gates. Not a fence company that added gates to the menu. Our technicians spend every working day diagnosing swing gates, slide gates, operators, hinges, posts, and welds across Lynwood. That focus shows up in how fast we identify a failure and whether we fix it in one visit. When a DoorKing board sputters or a Viking arm loses travel, we already know the failure patterns before we park.
Homeowners around Lynwood call us for a few consistent reasons. We work on the brand you already have, whether it’s a Viking, Ghost Controls, DoorKing, Elite, or another system. We don’t push replacement when a targeted repair will hold. And our estimate is free, with the price set in writing before any work starts. No mystery invoice after the fact.
Our gate repair team has handled hundreds of narrow-lot, root-tilted, rust-seized jobs in this city. We send a technician who understands that a gate on a 1948 Lynwood lot isn’t the same as one on a wide Carson driveway. The clearances, the shared posts, the aging concrete. It all matters.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding in Lynwood
Gate welding in Lynwood is often not a repair you can plan from a catalog. The city’s tight 90262 lots, with gate openings squeezed between stucco and block walls, mean many wrought-iron gates were custom-built on site and can’t be lifted off their hinges when they fail. A typical weld repair on a rusted ground-line hinge or a cracked frame joint runs $180 to $520, including grinding, prep, and touch-up. If we need to blast and rebuild an entire corner, it can reach $700 to $1,200 depending on how much decay is hiding under the paint.
In-Place Re-Welding
Some gates cannot be removed without cutting posts or dismantling a shared wall. On those, we weld in place. That means setting up shielding, grinding the failed joint clean, and re-welding with the gate still hinged. It’s slower and takes more skill, but it’s the only right way when the opening is too narrow for a lift.
Post Footings and Root Damage
Mature parkway trees along Lynwood’s older streets push roots through dry, aging concrete. A hinge post that tilts even half an inch throws a heavy ornamental gate out of plumb. We reset posts, pour new footings to proper depth, and re-square the frame so the gate clears again without dragging.
Commercial Gate Repair in Lynwood
Commercial gate repair in Lynwood runs from $350 for a basic hinge and latch fix on a chain-link swinging gate to $2,800 or more for a full slide-gate operator replacement with loop wiring and safety edge work. Small commercial properties here rely on gates for controlled access, tenant parking, and dumpster enclosures. When one fails, it’s not just a nuisance. It’s an access problem that can stop a delivery or block a tenant.
Slide Gates and Track Hardware
Slide gates come off their track when wheels wear, guides loosen, or debris builds in the rail. We realign the gate, replace wheels and bearings, and check that the motor isn’t fighting the track. A gate that strains is a gate that fails early.
Operators and Access Control
Commercial operators see far more cycles than a residential swing gate. A Viking or DoorKing unit that runs but doesn’t move usually means a broken drive gear, a dead capacitor, or a limit switch fault. We diagnose by brand, repair what’s repairable, and quote a replacement only when the old unit is genuinely finished.
Trusted Brands We Service in Lynwood
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Nine brands, one diagnostic approach: figure out what the system is supposed to do, test what it’s doing, and fix the difference. For Lynwood customers, we keep common boards, arms, remotes, and safety parts stocked on the truck, so a lot of jobs never need a second trip. We don’t steer you toward a brand we prefer. We repair the one you already own.
Common Gate Repair Problems We See in Lynwood Homes
After years of service across Lynwood, certain failures show up again and again. Here’s what we see most:
- Hinge posts tilted by parkway tree roots. On tight 90262 lots, mature trees send roots under gate posts and the old concrete can’t hold. The post leans, the gate sags, and heavy ornamental panels start dragging against block walls.
- Rusted ground-line welds seizing up. Winter rains and marine-layer damp find every old weld on a wrought-iron gate. Joints that looked fine in October bind and crack by March. We grind them out, re-weld, and seal so they last another cycle.
- Operator travel lost after heat or damp. Dry summer heat bakes the internals. Winter damp corrodes terminals. Either way, the operator runs but the gate doesn’t move correctly. Limit switches and force settings need readjusting.
- Gates that can’t be lifted off their hinges. On many narrow Lynwood lots, the opening between stucco and block is too tight to remove a welded gate. Repairs have to be done in place, which changes the whole approach. We’re set up for that.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Lynwood, CA
Here are honest, typical numbers for Lynwood’s market. A hinge repair or latch replacement runs $180 to $340. Realigning a sagging welded gate with post adjustment lands between $250 and $600. A full post reset with new concrete footing is $400 to $950 depending on root removal and access. Operator board replacement for a LiftMaster or DoorKing swings from $280 to $800 installed. Full slide-gate operator replacement can run $1,400 to $2,800 with safety edges and loop wiring. These are estimates, not quotes. Your written estimate sets the final price before work starts. Call (866) 569-6161 and we’ll walk you through it. Estimates are free.
We Also Serve Cities Near Lynwood
Our technicians cover Lynwood and the surrounding area, including Watts, Florence-Graham, Compton, and Carson. We’re based in Lynwood‘s service region with local knowledge of every neighborhood’s gate styles and problem patterns. If you’re a few blocks over the city line, call anyway. We’re already working nearby.
Serving Lynwood, CA – Our Local Coverage Area
We serve Lynwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Lynwood
Because the hinge post itself is usually moving, not the hinge bolts. On Lynwood’s narrow 90262 lots, mature parkway tree roots lift and tilt posts set in aging concrete. Tightening hinge bolts won’t fix a leaning post. We reset the post footing and re-square the frame, which is a $400 to $950 job depending on root work and how much concrete has to come out. Call (866) 569-6161 if you can see daylight shifting between the gate and wall.
Yes. In-place re-welding is standard practice for us in Lynwood. Many gate openings here are too narrow to lift the gate off its hinges. We weld with the gate still mounted, shielding the surrounding wall and grinding failed joints clean before laying new material. A ground-line weld repair runs $180 to $520. Call (866) 569-6161 and describe what you see; we’ll tell you honestly whether it’s a one-visit fix.
An automatic gate should have working safety edges or photo beams that stop and reverse the gate when something is in its path. On a residential swing gate, photo sensors near the leading edge and the hinge pinch point are standard. We check and recalibrate these every time we service an operator. If yours beeps but won’t reverse, call (866) 569-6161. We’ll test it on the spot.
A sheared drive gear, a slipping clutch, or a broken chain connection usually. On Lynwood’s older steel slide gates we also see wheel bearings shot and the guide rails ground down from years of debris. The operator sounds fine because it’s still running. The mechanical link between it and the gate isn’t. We diagnose by brand and replace only what’s failed, starting at $280. Call (866) 569-6161 for a written estimate before any work starts.
Yes, and on schedule. Inland LA Basin heat dries out wooden gates and hinge bushings so seams open and hardware cracks. Then winter marine-layer damp gets into those cracks and rusts every bare weld. Lynwood iron gates swing in heat, stick in damp, and sag as roots push posts through old concrete. It’s a predictable cycle. We see it every season. Call (866) 569-6161 if your gate is binding, dragging, or no longer closing square. We’ll set it right.
Call Gate Repair Compton for Gate Repair in Lynwood
If your gate is dragging, sagging, sticking, or the operator quit, call (866) 569-6161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll give you a straight diagnosis and a free written estimate before any work begins. In-place welding, post setting, operator repair, safety edge work. It’s all part of what we do. And gates are all we do.
Written by Todd Conway, Owner at Gate Repair Compton, serving Lynwood since 2014.