Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Lynwood, CA
Gate installation in Lynwood runs into a specific problem on nearly every block: the lots are narrow, the homes are older, and the driveway gates sit tight against stucco walls, shared fences, and mature parkway trees. Most jobs here are custom-fit because standard panels simply don’t clear the opening. We’re Gate Repair Compton, a gate-only specialist serving Lynwood with installation, repair, and automation work on both manual and electric systems. Call (866) 569-6161 for a free estimate. We answer 24/7.
Why Lynwood Homes Are Different
Lynwood’s housing stock is mostly 1940s through 1960s one-story stucco tract homes on narrow lots. Driveways run long and straight back to detached garages, and gates sit where the driveway meets the street or the alley, often welded between wood and block walls. The opening width is whatever the original builder left, which was rarely designed for a gate at all. That means a new gate in Lynwood is almost always a weld-in-place job. There’s no room to swing a standard panel wide, no clearance for off-the-shelf retrofit kits, and in many cases the gate frames had to be re-welded on site because the opening is too narrow to remove the gate once it’s hung.
The climate works against older iron and wood in predictable ways. Inland LA Basin heat and dry summers bake wooden gates until they warp and pull at the hinges. Winter rains and the marine-layer damp that settles over Lynwood find every rusted weld and every post that’s been losing its battle at the ground line. Original posts set in aging concrete tilt as the concrete spalls and the surrounding soil shifts. We see the same pattern each season: gates that stick in summer, sag in winter, and post bases that have rusted through just below grade where nobody noticed until the gate started dragging.
Another Lynwood-specific condition: mature parkway trees and shared block walls squeeze driveway gates from both sides. Roots push posts out of plumb. Block walls settle independently of the gate frame, which means a gate that swung fine two years ago now scrapes the latch post or binds at the strike. Neighbors’ gates often share a post or sit close enough that sightlines and swing clearances affect both properties. When we set a gate in Lynwood, we’re working within an opening that was never meant to hold automation and usually needs more than hardware, it needs a frame correction first.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Lynwood Services
Most Lynwood homeowners call us for one of two things: a gate that no longer moves the way it should, or an electric system that stopped responding. Both are covered by dedicated teams, and both start with a free on-site estimate.
Gate Repair in Lynwood
Manual gates in Lynwood fail in ways that are tied directly to the housing stock. Welded iron gates rust at the ground line where sprinkler overspray and winter damp sit against bare metal. Wood gates warp in the inland heat and pull hinges out of aging stucco. Posts tilt as roots from parkway trees push against footings. Repair means more than swapping a hinge or straightening a picket. We cut out the rusted section, re-weld the frame, reset the post if the footing has shifted, and re-align the gate so the latch actually catches. Read more about how we handle these jobs on our Gate Repair in Lynwood page.
Electric Gate Repair in Lynwood
Electric gates in Lynwood sit on older properties where the original wiring was often an afterthought. Operators get cooked by heat that builds against stucco walls and block fences. Control boards get damaged by voltage drops on circuits that were never sized for automation. Safety sensors misalign when posts shift. When an automated gate stops responding, the fix usually involves tracing the circuit, testing the operator’s logic, and checking every limit switch and safety edge. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems without trying to sell you a brand you don’t need. Details are on our Electric Gate Repair in Lynwood page.
Gate Installation in Lynwood
Gate installation in Lynwood usually means building a gate to fit an opening that was never standard. The pre-1960 homes here have driveways framed by stucco walls, shared block fences, and tree roots that have shifted every post over the decades. New construction in this city is measured, welded, and set to the actual dimensions of the opening, not ordered from a catalog. That’s why we treat Gate Installation as a custom job every time. The written estimate covers the full scope: posts, frame, hardware, and if you want it, automation and wiring.
Automatic Gate Installation
Signs you need it
You’re tired of getting out of the car to open and close the gate every time, or you want controlled access to a driveway that backs up to an alley or a busy Lynwood street.
What it costs in Lynwood
Automatic gate installation in Lynwood typically runs $2,800 to $7,500 depending on gate size, operator type, and how much electrical work the existing circuit needs.
How we do it
We measure the opening, set or reset the posts to hold the additional weight, hang the gate, mount the operator, run the low-voltage wiring, and program remotes and safety edges before testing the full cycle.
Driveway Gate Installation
Signs you need it
The driveway opens onto the street with no barrier, or an old chain-link gate is rusted through and no longer closes properly.
What it costs in Lynwood
Driveway gate installation in Lynwood typically runs $1,800 to $5,500, with wrought-iron and custom-fit frames on the higher end of that range.
How we do it
We pull the old gate if there is one, check the existing posts for plumb and rust, set new posts where needed, and weld or hang the new gate to clear the full swing without hitting stucco, block, or tree growth.
Sliding Gate Installation
Signs you need it
The driveway is too short or the setback too tight for a swinging gate, common on Lynwood lots where the house sits close to the street and a swing would hit the car or the wall.
What it costs in Lynwood
Sliding gate installation in Lynwood typically runs $2,500 to $8,000 depending on track length, gate weight, and whether you’re adding an automated operator.
How we do it
We build the gate to ride on a steel track or cantilever system, set the track bed and stop posts, hang the panel, and if automation is part of the job, install the operator and safety loops before load-testing the slide.
What Gate Installation Costs in Lynwood
| Item | Typical range in Lynwood |
|---|---|
| Manual gate installation | $1,800 – $5,500 |
| Automatic gate installation | $2,800 – $7,500 |
| Sliding gate installation | $2,500 – $8,000 |
Those ranges reflect what we see on Lynwood properties: custom-fit panels, post work in aging concrete, and electrical runs through older panels. The written estimate sets the final price before any work starts.
Does a new gate in Lynwood need a permit?
Most cities require a permit when posts are set in concrete or when electrical work is added for an operator. Lynwood is no different. We’ll tell you what applies to your job and can confirm the requirements with the city before we start.
Can you automate a gate that was originally manual?
Usually yes, but it depends on the gate’s weight, the post condition, and whether there’s a circuit nearby. On Lynwood’s older homes we often have to run a new dedicated line from the panel, which is part of the estimate we provide before any work begins.
Brands We Service in Lynwood
We work on the brand you already have rather than pushing a replacement you don’t need. In Lynwood we regularly service Viking, Ghost Controls, DoorKing, and Elite systems, among others. Replacement parts and common control boards are stocked on our trucks, so most repairs don’t wait on a parts order. See our brands for the full picture.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Lynwood, CA
| Service | Typical range in Lynwood |
|---|---|
| Manual gate repair | $150 – $550 |
| Electric gate repair | $225 – $850 |
| Operator replacement | $700 – $1,800 |
| Control board replacement | $300 – $800 |
| Safety sensor replacement | $175 – $450 |
| Gate wheel and track repair | $200 – $600 |
| Hinge and weld repair | $150 – $500 |
| Manual gate installation | $1,800 – $5,500 |
| Automatic gate installation | $2,800 – $7,500 |
| Sliding gate installation | $2,500 – $8,000 |
| Full gate replacement | $2,000 – $6,500 |
| Custom gate design and build | $2,500 – $8,000 |
What pushes a Lynwood price up is the lot itself: narrow openings that force custom fabrication, posts that have to be cut out and re-set in fresh concrete, and root systems from mature parkway trees that have shifted the original footings. Every job is priced by written estimate before work starts, and that’s the number you pay. No surprises after the gate is hung.
Neighborhoods We Serve in Lynwood
We cover the full ZIP code 90262, from the streets off Long Beach Boulevard through the residential blocks east toward the 710 and north and south along the city’s older tract developments. The neighborhoods here share the same lot patterns, the same gate problems, and the same fix-by-welding reality. Typical response for most Lynwood jobs is fast dispatch from 7am to 7pm.
- Central Lynwood
- Lynwood Gardens area
- Streets off Imperial Highway
- Neighborhoods along Long Beach Boulevard
- Blocks west of the 710
Service Area – Cities Near Lynwood
Gate Repair Compton covers Lynwood and the surrounding South LA and Gateway Cities areas. If you’re nearby, we also work in Watts, CA, Florence-Graham, CA, Compton, CA, and Carson, CA. Same gate-only focus, same brand coverage, same free estimate.
Serving Lynwood, CA – Our Local Coverage Area
We serve Lynwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Lynwood
We answer 24/7 and dispatch technicians from 7am to 7pm, Sunday through Friday. Most Lynwood repairs are scheduled same-day or next-day. Call (866) 569-6161 and we’ll get you on the schedule for the first available opening.
Some Lynwood neighborhoods have active HOAs or block associations that review exterior changes including gates and fencing. If yours does, we’ll work from the approved spec, but you’ll want to check your HOA’s rules before we order materials. The gate itself is the easy part.
Yes. That’s the point of working with a gate-only specialist. We install the gate, the operator, the safety edges, keypads, remotes, and the low-voltage wiring to the panel. Manual or automated, it’s all one scope on one estimate.
If your gate is sagging, stuck, or completely dead in Lynwood, call (866) 569-6161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 30-60 min.
- 4You approve before work beginsNothing starts until you say go.
What Lynwood Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Gilbert Herrera"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Elena Martinez"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Elena Flores